Yes meter wiring diagram base socket phase entrance service wire figure This video provides one example of how to install an Omnimeter. Push3 spec sheet and installation instructions, Did you find it helpful? Sorry we couldn't be helpful.  You will need 1 Omnimeter and on 3-phase 4-wire systems have 3 hot wires and a neutral wire. meter kwh Modified on: Wed, 30 Mar, 2022 at 10:01 AM. No. Help us improve this article with your feedback. Single phase 3-wire systems (some call them two phase or Edison) have 2 hot wires and a neutral wire. wiring Modified on: Tue, 29 Mar, 2022 at 4:43 PM. Yes If you had purchased your Omnimeters separately then you will need to contact EKM to have them assign the Omnimeter serial numbers to your Push3 gateway. After booting the Push3 will look for an available firmware update. Installation instructions for use with the EKM-Omnimeter II UL v.3: Use a small standard screwdriver to install one strand of twisted pair wire from terminal 20 (A) on your Omnimeter to the RS-485 (A) terminal block of the EKM Push3. Assuming that your meters are installed correctly, and you have followed the appropriate instructions, your EKM Push3 should already be pushing data over the internet to our cloud database. meter submeter pulse install d4e watthour clean test email type If you purchase your Omnimeter(s) and EKM Push3 together then the Push3 should be plug-and-play when you receive your order. No additional hardware or software is necessary in order for your EKM Push to send your Omnimeter data to the cloud. If a new firmware version is available, the Push3 will download it and update automatically. You can connect the EKM Push3 to your Wifi network, or you can connect an ethernet cable from you internet router to the ethernet port in your EKM Push. No. If you purchase your Omnimeter(s) and EKM Push3 together then the Push3 should be plug-and-play when you receive your order. Twisted pair wire for the RS-485 data connections. Do not use both. The email includes your EKM Push account key, which provides administrative access to your Push account and your meter data. Help us improve this article with your feedback. Use a small standard screwdriver to install one strand of twisted pair wire from terminal 12 (B) on your Omnimeter to the RS-485 (B) terminal block of the EKM Push3. The use and installation of 485Bees is explained in the video above. meter submeter pulse install d4e watthour clean test email type  These are generally older 3-phase systems. Sorry we couldn't be helpful. In this case the meter is an Omnimeter Pulse v.4 but installing a v.3 or v.5 Omnimeter is done in a very similar way. This video provides one example of how to install an Omnimeter. wiring Use the barrel jack port or the +/- terminal block. meter wiring diagram base socket phase entrance service wire figure Installation instructions for use with the v.4/5 Omnimeter models: Booting the Push3 gateway takes ~4 minutes. Here is a video showing proper wiring of an Omnimeter I v.3 installed on a 120 volt electrical system: Here is a video showing proper wiringof an Omnim Single-Phase 2-wire 120 volt, 240 volt, 230 volt (non-U.S.) Metering, Single-Phase 3-Wire 120/240V or 120/208V Metering, Electricity and/or Water and/or Gas Metering. If you cannot hardware the Omnimeter to the Push3, then you can wirelessly bridge the RS-485 communication using 485Bee zigbee radio modules. The images and diagrams shown here are in no way exhaustive. The video also describes how to read the Omnimeter with a computer via direct connection, how to make meter settings, how to setup a wireless connection to read the meter remotely, and how to install the EKM Push (now Push3) gateway for cloud-based data. It will have been pre-assign We don't work closely with installers so we can't give you qualified recommendations of who should install our products. It will have been pre-assigned to read the Omnimeters that you purchased. There are in fact many possible ways to install an Omnimeter. Use a small standard screwdriver to install one strand of twisted pair wire from terminal 21 (B) on your Omnimeter to the RS-485 (B) terminal block of the EKM Push3. To learn how to access all of your meter data, please refer to the EKM Push account information email that we sent out when the system was purchased. Fuse Installation and Wiring the Breaker Panel, Installing the Meter and Current Transformers, Installing 485Bee Radios and the EKM Push Gateway. Situational variables will determine how your installation may differ but this video should at least provide some of the basic principles you should consider when installing your metering system. Installation instructions for use with the EKM-Omnimeter I v.3: Use a small standard screwdriver to install one strand of twisted pair wire from terminal 11 (A) on your Omnimeter to the RS-485 (A) terminal block of the EKM Push3. meter kwh Connect the 12V DC power adapter from any 110-240V AC outlet to the appropriate port on your EKM Push3. We also included a hard copy of that email with the first order. You can use your key to log in to your Push Account Portal here: https://api.ekmpush.com/account.html?key=*enter*key*here*.  This is the most common residential syste 3-phase 3-wire systems have 3 hot wires and NO neutral wire.  This could be a 480/277 volt system, or a 120/208 volt system. There are in fact many possible ways to install an Omnimeter. The account portal allows you to see the status of all of your meters and gateways, as well as craft API queries and make meter settings. EKM Push3 installation from Appalachian DIY: Small 3mm standard screwdriver (included), Twisted pair wire for the RS-485 data connections (sold separately), Ethernet cable if not connecting to WiFi (sold separately). Connect the 12V DC power adapter from any 110-240V AC outlet to the appropriate port on your EKM Push3. Use the barrel jack port or the +/- terminal block. Only share this key with parties that you wish to provide this level of privileges. Here is another installation video from Appalachian DIY: Did you find it helpful? You can use the following links to jump to specific video parts: Part 3 - Testing, Pulling Wires, and Labeling, Part 4 - Fuse Installation and Wiring the Breaker Panel, Part 6 - Installing the Meter and Current Transformers, Part 9 - Installing 485Bee Radios and the EKM Push Gateway. It can take up to 30 minutes for the update to complete.